Ad Clicks : Ad Views : Ad Clicks : Ad Views : Ad Clicks : Ad Views : Ad Clicks : Ad Views :
Oh Snap!

Please turnoff your ad blocking mode for viewing your site content

Home / Paint / Lowes Behr Paint

Lowes Behr Paint

Lowes Behr Paint

Lowes Behr Paint -Interior painting requires as careful preparation of surfaces as does exterior painting. The advent of odorless paints now makes it possible to paint whenever of the year. Formerly, most interior painting in your home was over in the fall or spring, if this was possible to go out of the windows open to ventilate the room. But open windows brought dust into the room to mar the finished painted surface.

A good interior paint job can often be 50% preparation and 50% painting. Do not rush in preparing the surfaces within your eagerness to access the brush or roller. If you do not prepare the surfaces properly, you will be back using the paint brush or roller using some monthsLowes Behr Paint. In this section there is the necessary information on the application of several types of paints on various interior wall, ceiling and floor materials.

Plaster

New dry plaster in excellent, which would be to be finished a paint apart from water paint, ought to be given a coat of primer-sealer and permitted to dry thoroughly before being inspected for uniformity of appearance. Variations in gloss and color differences in the case of tinted primers indicate set up whole surface may be completely sealed. If not, an extra coat of primer-sealer ought to be applied. If only a number of "suction spots" are apparent, an extra coat through these areas could be sufficient.

A flat, semi-gloss, or high-gloss finish could be placed on the primed surface. For a flat finish, two coats of flat wall paint should follow the priming coat. For a semi-gloss finish, one coat of flat wall paint the other coat of semi-gloss paint ought to be placed on the primed surface. For a high-gloss finish, one coat of semi-gloss paint the other coat of high-gloss enamel ought to be used on the priming coat.

Before applying water paints with the calcimine type to new plastered walls they ought to be sized, using the glue-water size or, if your plaster is dry, a thin varnish or primer-sealer.

Cold water paints with the casein type could be applied either straight away to a plastered surface, or the surface could be first given a coat of primer-sealer to equalize uneven suction effects. The same is true of resin-emulsion paints, using the recommendations with the manufacturer with the product being given preference in the case of doubt. Since resin-emulsion paints usually contain some oil in the binder, they should ordinarily be reproduced just to plaster which includes dried thoroughly.

Texture wall paints may also be used on plaster surfaces. The advantages of this type of paint are that one coat economically creates a textured decoration and relieves the monotony of smooth flat paint. It also covers cracks or patches in the plaster more completely than ordinary wall paint. The disadvantages of texture wall paint are that they can Collect dust and so are tough to restore to some smooth finish. These materials can be found as water-or oil-based paints, are thicker than ordinary wall paints, and could be placed on wallboard and also plaster to generate textured effects including random, Spanish, mission, and multicolored.

Composition Wallboard

Composition wallboard usually presents no particular painting difficulties if your ordinary precautions are observed, including ensuring that this surface is dry and totally free of grease and oil. The painting procedure for wallboard is equivalent to for plaster; it requires a priming and sealing coat then whatever finishes coats are desired, or could be given one-coat flat or resin-emulsion type paint.

Wallpaper

Water-thinned paint could be placed on wallpaper that's well- bonded on the wall and does not contain dyes that might bleed in the paint. One thickness of wallpaper is preferable for paint application. Paints apart from those with the water-thinned type can also be placed on wallpaper following the directions given for painting plaster. However, wallpaper coated with your a paint is tough to remove without injury on the plaster.

Wood Walls and Trim

New interior walls and wood trim ought to be smoothed with sand-paper and dusted before painting or varnishing. To preserve the grain with the wood, the surface could be rubbed with linseed oil, varnished or shellacked, and waxed. If an opaque finish is desired, semi-gloss paint thinned with 1 pint of turpen-tine per gallon of paint or the primer-sealer previously described for walls could be used as a priming coat on wood. One or two coats of semi-gloss paint should then be reproduced on the thoroughly dry prime coat, or if a full-gloss finish is desired, the last coat ought to be a high-gloss enamel.

Masonry Walls and Ceilings

Interior masonry walls and ceilings above grade may, generally speaking, be painted in quite similar manner as plaster surfaces. Here again, it's important to allow adequate time for that masonry to dry before applying paint and, additionally, attention ought to be given on the preparation with the surface. When decorating a wall containing Portland cement (concrete, for instance), it is essential to take precautions from the attack of alkali. For this purpose, alkali-resistant primers including rubber-base paints could be used when oil paints will be to follow.

Cement-water paints are best designed for application to basement walls that are damp as a result of leakage or condensation. To apply these paints, a similar procedure ought to be followed as they are described for painting exterior masonry walls.

Concrete Floors

Two general kinds of paints for concrete floors are varnish and rubber-base paint. Each has its limitations as well as the finish cannot be patched minus the patched area showing through. Floor and deck enamel with the varnish type gives good service on concrete floors above grade its keep is no moisture present.

Rubber-base paints, which dry to some hard semi-gloss finish, could be used on concrete floors below grade, supplying the floor isn't continually damp from seepage and condensation.

Paint really should not be placed on a concrete basement floor before concrete has aged for about a year. The floor ought to be dry when painted, local plumber for application being in the winter or originate (assuming there is some heating apparatus in the basement), if the humidity in the basement is low. In general, three coats of paint are needed while on an unpainted floor, as well as the first coat ought to be thin to secure good penetration. After the paint is dry, it ought to be protected which has a coat of floor wax.

Lowes Behr Paint

In repainting concrete floors, where the existing paint may be waxed and it is in excellent except for some worn areas, the surface ought to be scrubbed with cloths saturated with turpentine or petroleum spirits and rubbed with steel wool while wet, to eliminate all wax before repainting. If this isn't done, the paint is not going to adhere and dry satisfactorily, if your old paint is badly worn, it ought to be removed by treating which has a solution of 2 lbs. of caustic soda (household lye) to 1 gallon of domestic hot water. This could be mopped on the surface and permitted to remain for 30 minutes then the bottom can be washed with domestic hot water and scraped which has a wide steel scraper. Another method of application would be to spread a thin layer of sawdust, which may be soaked in caustic solution on the floor and invite it to face overnight. The following morning, the bottom can be washed with domestic hot water as well as the paint scraped off Lowes Behr Paint. The surface should then be rinsed thoroughly with clean water.

If rubber-base paint may be used, the caustic soda treatment may not be effective and yes it could be important to make use of an organic solvent sort of paint remover.

Caution: - When using caustic soda or lye, avoid splashing eyes, skin, and clothing.

Interior Metal

Interior metal, including heating grilles, radiators, and exposed water pipes, ought to be painted to stop rust and to make sure they are as inconspicuous as possible. New metal ought to be cleaned of grease and dirt by washing with mineral spirits, and any rust ought to be removed by sanding, then a metallic primer ought to be applied. The finish coat could be the flat wall paint or perhaps a semi-gloss enamel.

If you aren't sure with the primer to make use of on metal, the paint dealer or manufacturer gives you this info, dependent on the sort of metal being painted Lowes Behr Paint.
Usually on exposed air ducts of galvanized metal a primer coat of zinc dust-zinc oxide paint is employed, prior to the finish coat is applied.
The paints could be applied by brush or spray; the small spray attachment for hoovers is quite convenient, specifically painting radiators.

Brass light fittings and andirons could be polished and kept bright by coating with metal lacquers. The lacquers, locked in cans pressurized, could be sprayed straight from the container. Old-fashioned or unattractive light fittings could be painted with ceiling or wall paint to harmonize using the surrounding surfaces.

Special Surfaces

WHITEWASH

Whitewashes and lime paints must be thin when applied. In fact, greatest results will likely be obtained if your application is so thin that this surface to which it is applied may be seen over the film while it is wet. The coating will dry opaque, but two thin Coats gives better results than one thick coat.

A large whitewash brush is best for applying the wash Lowes Behr Paint. One should not attempt to brush your coating, like applying oil paint, however spread the whitewash on as evenly and quickly as possible.

The principal ingredient in whitewash is lime paste. A satisfactory paste can be made with hydrated lime, but better results are obtained by utilizing quicklime paste that may be slaked with sufficient water to restore moderately stiff. The lime paste ought to be held in a loosely covered container for about a couple of days. Eight gallons of stiff lime paste can be made by slaking 25 lbs. of quicklime in 10 gallons of water, or by soaking 50 lbs. of hydrated lime in 6 gallons of water. After soaking, the paste ought to be strained by way of a fine screen to eliminate lumps or foreign matter.

Whitewash can be made from various combinations of lime paste and other ingredients. The following two formulas are satisfactory.

The casein, which is the glue binder, ought to be soaked in 2 gallons of domestic hot water until thoroughly softened, which ought to be approximately 2 hours. After dissolving the trisodium phosphate in 1 gallon of water it ought to be added on the casein, stirring the mixture before casein dissolves. This solution ought to be mixed using the lime paste and 3 gallons of water.

The salt and alum ought to be dis-solved in 4 gallons of domestic hot water, then the molasses could be added on the mixture. The resulting clear option would be then added on the lime paste, stirred vigorously, and thinned with water on the desired consistency. This whitewash includes a yellow tinge when first applied, but the color disappears using some days leaving a white film.

Another satisfactory whitewash can be made by diluting a moderately heavy cold lime paste (about 33 lbs. of hydrated lime and 8 gallons of water) with 5 gallons of skim-milk.

The area paid by a gallon of whitewash is determined by the type with the surface, but ordinarily a gallon will take care of about 225 sq. ft. on wood, about 180 sq. ft. on brick, and about 270 sq. ft. on plaster. The formulas mentioned will make from 10 to 14 gallons of whitewash. If a smaller quantity is desired, the quantity of each ingredient ought to be reduced proportionately.

STIPPLING

Whether you want the consequence of stippling (tiny paint dots) as a decorative effect, or if you do have a wall which includes an uneven surface and you feel you can hide the defect by stippling it, you might accomplish this result very simply.

For stippling you will need a special brush; acquire one that's flat, and possesses short, stiff bristles.

The initial step would be to cover the surface which has a coat of paint, with your regular paint brush, or spray, or roller. Then, while the surface remains wet, consider the dry stipple brush and energetically with short strokes drive the ends or the bristles in the wet paint. Be sure not to brush across. The result will likely be clusters of dots. Every couple of minutes wipe the brush which has a cloth, to help keep the bristle ends clean and dry.

STENCILING

You might want designs on the walls, or simply even on floors and ceilings, in certain with the rooms or hallway. You may buy or build your own stencils, which ought to be on heavy paper, stencil board, plastic, or metal. Avoid stencils created from lightweight paper that will get soaked when touched by wet paint. Your paint dealer will suggest the top paint for you to make use of, as it will depend a great deal on the surface over which you need to squeeze stenciled designs. Generally a heavy paint is employed, in order that it is not going to spread under the stencil while you are applying it.

The stencil must be held very firmly against the surface with one hand, as well as the stencil brush worked over it quickly using the other hand Lowes Behr Paint. Or, in case you have an assistant, it is best for starters person to help keep the stencil steady, while the other does the painting. In removing the stencil, be sure to get it without smudging.

  • Facebook
  • Twitter
  • Google+
  • Linkedin
  • Pinterest

Leave a Comment

Your email address will not be published. Required fields are marked *

This div height required for enabling the sticky sidebar